When it is used in a remote room with a sensor that is connected to the Multiroom IR jack f, this button will raise or lower the volume in the remote room. When it is used in a remote room with a sensor that is connected to the Multiroom IR jack f, this button will temporarily silence the feed to the remote room only. Press the button again to return to the previous volume level. See page 36 for complete information on using the Multiroom system. After unpacking the unit, and placing it on a solid surface capable of supporting its weight, you will need to make the connections to your audio and video equipment.
We recommend that you use high-quality interconnect cables when making connections to source equipment and recorders to preserve the integrity of the signals. NOTE: When the CD player has both fixed and variable audio outputs, it is best to use the fixed output unless you find that the input to the receiver is so low that the sound is noisy, or so high that the signal is distorted. Assemble the AM Loop Antenna supplied with the unit as shown below.
Connect it to the. The FM antenna may be an external roof antenna, an inside powered or wire-lead antenna or a connection from a cable TV system. Note that if the antenna or connection uses ohm twin-lead cable, you must use the ohm-toohm. To ensure that all the audio signals are carried to your speakers without loss of clarity or resolution, we suggest that you use high-quality speaker cable. Many brands of cable are available and the choice of cable may be influenced by the distance between your speakers and the receiver, the type of speakers you use, personal preferences and other factors.
Your dealer or installer is a valuable resource to consult in selecting the proper cable. Regardless of the brand of cable selected, we recommend that you use a cable constructed of multistrand copper with a gauge of 14 or smaller. Remember that in specifying cable, the lower the number, the thicker the cable. Cable with a gauge of 16 may be used for short runs of less than ten feet. We do not recommend that you use cables with an AWG equivalent of 18 or higher, due to the power loss and degradation in performance that will occur.
Cables that are run inside walls should have the appropriate markings to indicate listing with UL, CSA or other appropriate testing agency standards. When connecting wires to the speakers, be certain to observe proper polarity. NOTE: While most speaker manufacturers adhere to an industry convention of using black terminals for negative and red ones for positive, some manufacturers may vary from this configuration. We also recommend that the length of cable used to connect speaker pairs be identical.
For example, use the same length piece of cable to connect the front-left and front-right or surround-left and surround-right speakers, even if the speakers are a different distance from the AVR When a passive subwoofer is used, the connection first goes to a power amplifier, which will be connected to one or more subwoofer speakers.
If you are using a powered subwoofer that does not have line-level input connections, follow the instructions furnished with the speaker for connection information.
If an external multi-channel audio source with 5. If an external multi-channel audio source with 7. Video equipment is connected in the same manner as audio components. Again, the use of highquality interconnect cables is recommended to preserve signal quality. Connect the analog audio and video outputs of a satellite receiver, cable TV converter or.
Video 3 j 35 jacks. If your DVD player and monitor both have component video connections, connect the component outputs of the DVD player to the. Note that even when component video connections are used, the audio connections should still be made to either the analog DVD Audio Inputs.
If another component video device is available, connect it to the Video 2 Component Video Input Jacks a. The audio connections for this device should be made to either the.
If the component video inputs are used, connect the Component Video Output b to the component video inputs of your TV, projector or display device. A device connected here is selected as the Video 4 input, and the digital inputs must be assigned to the Video 4 input.
See page 20 for more information on input configuration. However, it will not convert composite or S signals to component video. The AVR is designed for flexible use with multiroom systems, external control components and power amplifiers. If the receiver is placed behind a solid or smoked glass cabinet door, the obstruction may prevent the remote sensor from receiving commands. In this event, an optional remote sensor may be used. Connect the output of the remote sensor to the Remote IR Input jack e.
If other components are also prevented from receiving remote commands, only one sensor is needed. If other Harman Kardon compatible source equipment is part of the main room installation, the Remote IR Output jack d on the rear panel should be connected to the IR IN jack on source equipment. This will enable the remote room location to control source equipment functions. Depending on the distance from the AVR to the remote room, two options are available for audio connection:.
In the remote room, connect the interconnect cable to a stereo power amplifier. Run high-quali- ty speaker wire from the amplifier to the speakers in the remote room. Alternatively, you may install an optional volume control between the output of the amplifiers and the speakers. This unit is equipped with two accessory AC outlets. They may be used to power accessory devices, but they should not be used with highcurrent draw equipment such as power amplifiers.
The total power draw to each outlet may not exceed watts. NOTE: Many audio and video products go into a Standby mode when they are used with switched outlets, and cannot be fully turned on using the outlet alone without a remote control command.
Finally, when all connections are complete, plug the power cord into a nonswitched volt AC wall outlet. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Typographical Conventions In order to help you use this manual with the remote control, front panel controls and rear panel connections, certain conventions have been used.
Thank you for choosing Harman Kardon! With the purchase of a Harman Kardon AVR you are about to begin many years of listening enjoyment. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance. Do Not Open the Cabinet There are no user-serviceable components inside this product. CATV or Antenna Grounding If an outside antenna or cable system is connected to this product, be certain that it is grounded so as to provide some protection against voltage surges and static charges.
Cleaning When the unit gets dirty, wipe it with a clean, soft, dry cloth. Moving the Unit Before moving the unit, be certain to disconnect any interconnection cords with other components, and make certain that you disconnect the unit from the AC outlet.
Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Harman Kardon AVR owners to properly answer your question. This manual comes under the category Receivers and has been rated by 1 people with an average of a 5.
This manual is available in the following languages: English. Is your question not listed? Power for the Digital Revolution. Ask a question. Power for the Digital Revolution. Ask a question. Rick, No comments 0. Answer this question Send. Harman Kardon AVR specifications. Related product manuals. When is my volume too loud? Find your manual. Account created Please check your e-mail in order to activate your account. Hifi-Manuals uses Cookies exclusively to gather anonymous data that help us improve the website.
This data is collected and thus shared with Google.
0コメント